Hello and welcome to our community! Is this your first visit?
Register
  • Twitter

  • Latest Flight Videos

    mackar

    Sandhammaren beach and lighthouse

    Thread Starter: mackar

    Last Post By: mackar 09-28-2014, 02:14 PM Go to last post
    mackar

    Naza V1 flyaway and crash

    Thread Starter: mackar

    For some reason my quad decided to take an own flight... at 2:20 in the video I start to turn right but then the quad turns left by itself and flies backwards

    Last Post By: Kenny9999 09-26-2014, 07:12 PM Go to last post
    JAB1a

    FPV Racing Mini Quadcopters Advanced Course

    Thread Starter: JAB1a

    Hi All,
    Such a fun day. A small West Devon FPV meet was organised by the guys from BBRC. The location was perfectly suited to this sport with different

    Last Post By: JAB1a 09-26-2014, 09:30 AM Go to last post
    mackar

    Stockholm Olympic Stadium from 1912

    Thread Starter: mackar

    Flying in the Stadium from 1912 Olympic games

    Last Post By: mackar 09-25-2014, 04:02 PM Go to last post
    mackar

    Early morning at the beach

    Thread Starter: mackar

    Last Post By: mackar 09-24-2014, 09:09 PM Go to last post
    dsmavis

    An Afternoon with Friends on Lake Jackson, Georgia

    Thread Starter: dsmavis

    A beautiful afternoon spent with great friends on Jackson Lake in Georgia.

    All video was shot with my GoPro Hero 3+ Silver edition camera.

    Last Post By: dsmavis 09-22-2014, 12:35 PM Go to last post
    JAB1a

    FPV Spanky Danescombe Valley Paper Mill

    Thread Starter: JAB1a

    Hi All,
    I managed to get two full flights done at this beautiful location (the full flight shown was my second flight), the air was very calm inside

    Last Post By: JAB1a 09-15-2014, 06:39 PM Go to last post
    dsmavis

    The Haunted Kudzu Forest

    Thread Starter: dsmavis

    No FPV yet, so all flying is within line of site. At times, I did get a good distance away from myself while down in the trees... right on the edge of

    Last Post By: dsmavis 09-10-2014, 11:34 AM Go to last post
    dsmavis

    Lloyd Shoals Dam -- Lake Jackson, Georgia

    Thread Starter: dsmavis

    My Homebuilt AeroQuad quadcopter bumming around the Dam at the South end of Jackson Lake in Georgia.

    No FPV yet, so all the flying is still

    Last Post By: dsmavis 08-29-2014, 05:57 PM Go to last post
  • Latest User Build Logs

    RobDrech

    3D Printed 635 Hex

    Hey Scott! I was actually thinking the same thing. I'm going to figure out way to have a removable tray that sits just above the landing gear that contains

    RobDrech 09-28-2014, 10:34 PM Go to last post
    jsmcms

    3D Printed 635 Hex

    Hi Rob,

    Nice design. You might solve some of your weight distribution problems by stacking another "star" below the existing center

    jsmcms 09-27-2014, 12:34 AM Go to last post
    ewingate

    3D Printed 635 Hex

    I've been using ABS printed motor mounts all summer, no issues with heat at all. I've broken a few mounts but I haven't bent a motor shaft or prop adapter

    ewingate 09-26-2014, 04:38 PM Go to last post
    RobDrech

    3D Printed 635 Hex

    Wooden is pretty spot on. I don't think properly cooled motors would get much above 100*F, the extrusion temperatures for ABS are 430*F, assuming that

    RobDrech 09-26-2014, 04:03 PM Go to last post
    wooden

    3D Printed 635 Hex

    I wouldn't expect it to - if your motors are getting that hot you're either flying like a madman or you've got some setup issue (wrong ESC timing, prop

    wooden 09-25-2014, 03:00 PM Go to last post
    allanGEE

    First Quad Assistance

    wooden +1, yamahabest +1

    allanGEE 09-25-2014, 01:35 PM Go to last post
    Avalonnw

    3D Printed 635 Hex

    RobDrech, I was actually thinking about Rostock Max2 or something similar.

    Back to topic, the motors can get quite hot, would it not affect

    Avalonnw 09-25-2014, 12:29 AM Go to last post
    yamahabest

    First Quad Assistance

    Oh, I am so sorry, I didn't know I had to respond to you within 24 hours...

    This attitude will get you very far in this hobby... Maybe someone

    yamahabest 09-24-2014, 07:42 PM Go to last post
    RobDrech

    3D Printed 635 Hex

    Wooden, I completely agree with your take on the landing gear, it's quite "light duty". I haven't decided on a better design yet so that one

    RobDrech 09-24-2014, 04:25 PM Go to last post
    wooden

    First Quad Assistance

    I don't think you understand how small this forum is - less than 10 people regularly post here... And to be honest, the 'first time builder, did I choose

    wooden 09-24-2014, 03:08 PM Go to last post
  • Visitors

  • Latest User Gallery Pictures

  • Kenny9999

    There is no available content written by Kenny9999